United States*
Microsoft.com Home|Site Map
Microsoft*
Search Microsoft.com for:
Help and Support 
|Select a Product|Search (KB)

Setting Up Windows NT on Motorola PowerStack When Drive Is New

Article ID:155407
Last Review:October 24, 2002
Revision:1.0
This article was previously published under Q155407

SUMMARY

This article describes the steps necessary to install Windows NT on a Motorola PowerStack computer, when the drive is new or has been low-level formatted. When all boot information on the drive is missing, the system will display the following information when the computer is started:

   AutoBoot about to begin.. Press <ESC> to Bypass, <SPC> to Continue
   Scanning System for Attached Mass Storage Devices
   Attempting BOOT from Device(s) of Type = FDISK
   Attempting BOOT from Device(s) of Type = CDROM
   Attempting BOOT from Device(s) of Type = TAPE
   Attempting BOOT from Device(s) of Type = HDISK

   Autoboot Failed
   PPC1-Diag>
				

If your computer is in this state, follow the instructions below.

MORE INFORMATION

The following materials must be available before beginning:

PPC Boot Disk (Available from Motorola)
Arcinst.exe (Available from Motorola)
FW.IMG on disk (Available from Motorola)
Windows NT compact disc (Available from Microsoft)
1.Start the computer from the PPC boot disk.
2.When the firmware loads:
a. Insert the disk that has Arcinst.exe in the floppy disk drive.
b. Select Run a Program.
c. In Program to Run type the following:

a:\arcinst
d. Press Enter.
3.Select Configure Partitions.
4.Select Create PowerPC Boot Partition. If more than one SCSI bus is available, select the appropriate SCSI bus. You will receive the following message:

Partition successfully created.
Press any key to continue...

The partition will be automatically formatted. Then the following message will be displayed:

Partition formatted successfully.
Press any key to continue
5.Press a key; the following prompt is shown:

Enter pathname for the PowerPC BootLoader:

Insert the disk with the correct Fw.img file into the floppy disk drive and type:

a:\fw.img

The following messages will be shown:

Reading ARC from:
multi(1)disk(0)fdisk(0)\fw.img
Load Image Size = 288000
Press any key to continue...

Boot Software Copied Successfully.
Press any key to continue...

Successfully installed PowerPC Boot Loader.
6.On the ARCINST menu select Create Partition. If required, select the appropriate SCSI bus.
7.At the "Enter the size in MB (1-1000):" prompt, type the size for the system partition; this will typically be 10 MB. The following message is displayed:

Partition successfully created.
Press any key to continue...

You will get this prompt:

Do you want to make this the system partition (y/n)?

Type 'y' (without quotation marks) and press ENTER. The partition will be automatically formatted. The "Partition formatted successfully" message will be displayed again. Press any key to continue.
8.Quit ARCINST.
9.On the firmware menu, select the "Run a program" option and type:

cd:\ppc\setupldr
10.Windows NT Setup will start. Setup can be used to partition the remainder of the drive and install a new copy of Windows NT.

The third-party products discussed here are manufactured by vendors independent of Microsoft; we make no warranty, implied or otherwise, regarding these products' performance or reliability.

APPLIES TO
Microsoft Windows NT Workstation 4.0 Developer Edition
Microsoft Windows NT Server 4.0 Standard Edition
Keywords: 
kbsetup kb3rdparty KB155407

Article Translations

 

Other Support Options

Contact Microsoft
Phone Numbers, Support Options and Pricing, Online Help, and more.
Customer Service
For non-technical assistance with product purchases, subscriptions, online services, events, training courses, corporate sales, piracy issues, and more.
Newsgroups
Pose a question to other users. Discussion groups and Forums about specific Microsoft products, technologies, and services.

©2006 Microsoft Corporation. All rights reserved. Terms of Use |Trademarks |Privacy Statement